Nicholasville Electrical Company serves homeowners, landlords, and commercial clients across Nicholasville and Jessamine County. The work runs the full range of residential and commercial electrical needs: a dead outlet that needs tracing, a panel that can no longer carry the load, a whole-home rewire, or a dedicated circuit for a new appliance. Whatever the job, the goal is the same. Safe wiring. Solid workmanship. Straight answers. We are available every day from 9:00 AM to 10:00 PM, so when something goes wrong, you do not have to wait until Monday morning to get it looked at.
Seeing flickering lights or a warm outlet? Those are the calls we take most often, and they are worth taking seriously. A flickering light can point to a loose connection, a failing breaker, or a load problem on the circuit. A warm or sparking outlet is a sign of something that should not wait. Burning smells, partial power loss, breakers that trip and will not reset, and outlets that simply stop working all fall into the same category: a fault that needs to be traced before it becomes something worse.
Troubleshooting starts with understanding what the circuit is doing and what it feeds. GFCI outlets in bathrooms, kitchens, and garages can trip and cut power to other outlets downstream, which is a common source of confusion. AFCI breakers, which protect against arc faults in bedroom and living area circuits, can also trip on a wiring issue that is not immediately obvious. We trace the fault. We fix the wiring. We restore the power. One call and we are on it.
Good electrical work isn't complicated, it's just done right, and panel work is where that matters most. Older homes in Jessamine County often carry 100-amp service panels that were adequate when the house was built but fall short under the demand of a modern household. Multiple window units, an electric range, a washer and dryer, a home office, and a garage with power tools all pull from the same panel. When the capacity is not there, breakers trip, circuits share loads they should not, and the risk of overheating goes up.
Panel replacement typically involves pulling the old panel, installing a new 200-amp service panel, and confirming that the grounding and bonding are correct throughout. Service-entrance and meter work, subpanel installation for a garage or workshop, and load calculations to size the upgrade correctly are all part of this category of work. Whole-home surge protection is often added at the same time, protecting appliances and electronics from voltage spikes on the utility line. Electrical work done to the standard the next inspection expects is what the job calls for, and that is what the job gets. Call and we'll get you back to full power.
Some homes need a full rewire. Others just need one outlet fixed. The range of wiring work we handle covers everything in between: whole-home rewiring for older properties, replacement of knob-and-tube wiring that no longer meets current standards, aluminum-wiring remediation for homes where aluminum branch circuits were installed in the 1960s and 1970s, and dedicated circuit installation for specific appliances and equipment.
Dedicated circuits matter more than most homeowners realize. A dryer, an electric oven, a refrigerator, a dishwasher, a microwave, a washer, and a hot tub each draw enough current to warrant a circuit of their own. Running them on shared circuits leads to nuisance trips at best and overheating at worst. An EV charger or a hot tub often means checking the panel first, because the circuit is only as useful as the capacity behind it. We confirm what the panel can carry before any new circuit is added, and if an upgrade is needed, that conversation happens before anything is scheduled.
When the job is done, we leave your home clean and powered, and that applies to the smaller jobs as much as the larger ones. Outlet installation and replacement covers standard outlets, GFCI outlets for wet locations, AFCI outlets for arc-fault protection, and USB outlets for rooms where charging is a regular need. Switch work includes standard replacements, three-way switch wiring for staircases and hallways, and dimmer installation for living areas and bedrooms.
Lighting covers more ground than most people expect. Recessed lighting in a kitchen or living room, ceiling fixtures in bedrooms and hallways, under-cabinet lighting for work surfaces, exterior and security lighting, landscape circuit wiring, motion sensor lights at entry points, and LED retrofit work all fall under this category. Ceiling fan installation and wiring fits here too, whether it is a straightforward swap or running a new circuit to a room that does not currently have a fan box. No pressure and no gimmicks, just safe, solid wiring from the first call to the finished job.
Nicholasville has a mix of housing that spans several decades of construction. Older neighborhoods near the center of town often carry wiring and panels from an era when 60-amp or 100-amp service was standard and branch circuits were not protected by arc-fault breakers. Knob-and-tube wiring shows up in some of the older properties, and aluminum branch circuit wiring is not uncommon in homes built between roughly 1965 and 1975. Neither is a reason to panic, but both require specific approaches rather than a generic repair.
Newer construction on the edges of Nicholasville and out into the county tends to have 200-amp service already in place, but those homes come with their own considerations: more circuits, more complex panel configurations, and a higher baseline of electrical demand from the start. Knowing what is typical in a given neighborhood helps scope a job accurately on the phone, before anyone drives out to the property.
Both EV charger installation and backup generator hookups start the same way: with a look at the panel. A Level 2 EV charger runs on a 240-volt dedicated circuit, typically a 50-amp circuit for most home chargers. If the panel does not have the capacity for that circuit, the panel conversation comes first. We size the circuit to the charger, confirm the panel can carry the added load, and run the wiring to wherever the charger will be mounted, whether that is in a garage, a carport, or on an exterior wall.
Generator hookup work covers the electrical side of connecting a backup generator: installing the transfer switch, running the wiring between the generator and the panel, and confirming that the connection is set up so utility power and generator power cannot feed back against each other. Standby generator wiring and manual transfer switch installation both fall into this category. A straightforward choice for homeowners and property managers who want backup power handled correctly rather than improvised.
An electrical safety inspection covers the condition of the panel, the type and age of wiring throughout the home, grounding and bonding, the presence of arc-fault and ground-fault protection where current standards call for it, and any visible hazards in accessible areas. These inspections are useful for buyers and sellers going through a real estate transaction, landlords reviewing a rental property, and anyone living in an older home who wants to understand what the wiring looks like before a problem surfaces. The inspection report gives you a clear picture of what is there and what, if anything, needs attention.
We cover Nicholasville and the surrounding communities throughout Jessamine County and the wider Bluegrass region. That includes Wilmore, Keene, Brannon Crossing, Harrodsburg, Versailles, and Richmond, as well as the rural stretches of the county between them. Whether the property is inside Nicholasville city limits or out in the county, the same range of electrical work applies. Call to confirm coverage at your address if you are on the outer edge of the area.
The scope and the price are settled on the call. When you call to describe the job, the goal is to understand what the work involves well enough to give you a rate before anything is scheduled. That means asking about the panel, the wiring, the location of the work, and what the symptom is. For a straightforward outlet replacement or ceiling fan install, the price is typically confirmed in that first conversation. For larger jobs like a panel upgrade or a whole-home rewire, the scope is confirmed before a visit is booked.
The same number you call to book the job is the number to call if you have a question about the work afterward. There is no separate billing line and no separate scheduling department. One number, one point of contact, start to finish.
Older neighborhoods near the center of Nicholasville often have 100-amp panels, knob-and-tube wiring, or aluminum branch circuits from the 1960s and 1970s. Knowing what is common in a given part of town lets us ask the right questions on the phone and arrive with a realistic picture of what the job is likely to involve. That reduces surprises once the work starts.
You reach someone who knows the trade and can scope the job on the phone. The person who answers can tell you what the visit involves, give you a rate, and get the appointment on the schedule. There is no separate scheduling department and no separate billing line.
If something unexpected turns up once the work is underway, we stop and explain what we found before continuing. The revised scope and any change to the price are discussed before additional work begins. You are not presented with a different bill at the end of the visit without that conversation happening first.
Call (859) 695-6995 and describe what you are seeing.
We will figure out whether it is related to the work that was done and what the next step looks like. The same number you used to book the job is the number to call with any follow-up question.
Electrical work in Kentucky is subject to the National Electrical Code as adopted by the state, and local inspectors enforce it. We perform the work to the standard the next inspection expects, which means correct breaker sizing, proper grounding and bonding, GFCI and AFCI protection where required, and materials rated for the application. Permit requirements depend on the scope of the job and are confirmed before work begins.
The scope, the price, and the scheduled time are all settled on the call. If anything changes before the visit, we communicate that before showing up. You know what the visit covers and what it costs before anyone comes to the property.
Good electrical work isn't complicated, it's just done right, and the same applies to how pricing works. When you call, you get a rate for the job. That rate is based on what the work involves, not a number pulled from a price sheet before anyone has heard the details. Common questions about cost come up on every call: what does a panel upgrade run, what does rewiring a room cost, what is the rate for an EV charger circuit, what does a generator hookup involve. Those questions get straight answers, not a callback or a form to fill out.
The price is confirmed before anything is scheduled. If the scope changes once the work starts because something unexpected turns up behind the wall, that conversation happens before the work continues, not after. For electrical work across Nicholasville and Jessamine County, the process is the same every time: call, describe the job, get a rate, schedule the visit. Call now and we'll set the appointment.
Reach us at (859) 695-6995.
(859) 695-6995